View ISD1620BPYI01_2375422.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

preliminary publication release date: jan. 23, 2007 revision 1.2 isd1600b series single-message single-chip 6.6- to 40-second voice record & playback devices with valert option
isd1600b series - 2 - table of contents 1. general description......................................................................................................... ......... 3 2. features .................................................................................................................... ..................... 4 3. block diagram ............................................................................................................... ............... 5 4. pin configuration ........................................................................................................... ............ 6 5. pin description ............................................................................................................. ................ 7 6. functional description...................................................................................................... ...... 9 6.1. detailed description ...................................................................................................... .............. 9 6.1.1 audio quality............................................................................................................ ........... 9 6.1.2 duration................................................................................................................. .............. 9 6.1.3 flash storage............................................................................................................ .......... 9 6.1.4 basic operation .......................................................................................................... ........ 9 6.1.5 valert ................................................................................................................... ................ 9 6.1.6 automatic power-down mode ............................................................................................ 9 6.2. functional description example............................................................................................ .... 10 6.2.1. record a message........................................................................................................ ... 10 6.2.2. edge-trigger playback ................................................................................................... ... 10 6.2.3. level- trigger playback ................................................................................................. ... 10 6.2.4. led operation ........................................................................................................... ...... 10 6.2.5. r osc operation................................................................................................................. 10 7. timing diagrams............................................................................................................. ............. 11 8. absolute maximum ratings.................................................................................................... 13 8.1 operating conditions....................................................................................................... ........... 14 9. electrical characteristics ................................................................................................. 1 5 9.1. dc parameters............................................................................................................. ............. 15 9.2. ac parameters ............................................................................................................. ............. 16 10. typical application circuit ................................................................................................ .17 11. package drawing and dimensions .................................................................................... 18 11.1. 16-lead 150mil small outline integrated circuit (soic) package ......................................... 18 11.2. 16-lead 300mil plastic dual inline package (pdip)............................................................... 19 11.3. die physical layout ...................................................................................................... ........... 20 12. ordering information....................................................................................................... .... 21 13. version history ............................................................................................................ ........... 22
isd1600b series publication release date: jan. 23, 2007 - 3 - revision 1.2 1. general description the winbond ? isd1600b chipcorder ? series is a high quality, fully integrated, single-chip single- message voice record and playback device ideally suited to a variety of electronic systems. the message duration is user selectable in ranges from 6.6 seconds to 40 seconds, depending on the specific device. the sampling frequency of each device can also be adjusted from 4 khz to 12 khz with an external resistor, giving the user greater flexibility in duration versus recording quality for each application. operating voltage spans a range from 2.4 v to 5.5 v to ensure that the isd1600b devices are optimized for a wide range of battery or line-powered applications. the devices include an on-chip osc illator (with external resistor cont rol), microphone preamplifier with automatic gain control (agc), ant i-aliasing filter, multi-level storage (mls) array, smoothing filter, pulse width modulation (pwm) class d speaker driver, and current output. voice signals can be fed into the chip through a differential microphone input for recording. the pwm output can directly drive a standard 8 speaker or a typical buzzer, while the separate single-ended current output can drive an external amplifier. recordings are stored into the on-chip flash memory cells, providing zero-power message storage. this unique single-chip solution is made possible through winbond?s patented multi-level storage (mls) technology. audio data are stored directly in solid-state memory without digital compression, providing superior quality voice and music reproduction. the isd1600b series also supports an optional ?valert? (voicealert) feature that can be used as a new message indicator. with valert, the ic strobes an external led to indicate that a new message is present.
isd1600b series - 4 - 2. features ? user-friendly single-chip, single-message voice record & playback devices ? wide operating voltage: 2.4v to 5.5v ? push-button interface o record is level-triggered o playback is either edge- or level-triggered ? selectable sampling freque ncy controlled by an external oscillator resistor sampling frequency 12 khz 8 khz 6.4 khz 5.3 khz 4 khz rosc 53 k 80 k 100 k 120 k 160 k ? variable duration selected by external oscillator resistor sample frequency 12 khz 8 khz 6.4 khz 5.3 khz 4 hkz isd1610b 6.6 secs 10 secs 12.5 secs 15 secs 20 secs isd1612b 8 secs 12 secs 15 secs 18 secs 24 secs isd1616b 10.6 secs 16 secs 20 secs 24 secs 32 secs isd1620b 13.3 secs 20 secs 25 secs 30 secs 40 secs ? message and operation indicators o optional valert (voicealert) to indicate the presence of new messages o led: stay on during recording, blink during playback operation ? automatic power-down mode o enters standby mode immediately after a record or playback cycle o standby current: 1a typical and 10a maximum ? dual output channels o pwm class d speaker amplifier to directly drive an 8 ? speaker or a typical buzzer o aud single-ended current output to drive external power amplifier ? chipcorder standard features o high-quality, natural voice and audio reproduction o zero-power message storage: eliminates battery backup circuits o 100-year message retention (typical) o 100,000 record cycles (typical) ? package options: leaded and lead-free packaged units ? available in die, 16l 150mil soic and 16l 300mil pdip ? temperature options: o commercial: 0 c to +50 c (die); 0 c to +70 c (packaged) o industrial: -40 c to +85 c (packaged)
isd1600b series publication release date: jan. 23, 2007 - 5 - revision 1.2 3. block diagram internal clock timing nonvolatile multilevel storage array analog transceivers decoders device control power conditioning automatic gain control (agc) active antialiasing filter active smoothing filter amp agc amp sampling clock sp+ sp- led playl playe rec v cca v ssa agc mic- mic+ r osc aud amp v ccd v ssd v ssp v ccp
isd1600b series - 6 - 4. pin configuration soic / pdip v ssd rec playe playl agc v ccd r osc sp+ v ssa v cca /v ccp led 16 15 14 13 12 11 10 1 2 3 4 5 6 7 mic- mic+ isd1600b v ssp 9 8 sp- aud
isd1600b series publication release date: jan. 23, 2007 - 7 - revision 1.2 5. pin description soic / pdip pin name pin no. functions v ssd 1 digital ground : v ssd is the ground for digital circuits. it is important to have a separate path for each ground back to the system ground terminal to minimize noise. rec 2 record : the device starts recording whenever rec transits from high to low and stays at low. recording stops when the signal returns to high. this pin has an internal pull-up resistor [1] and an internal debo unce on fa lling edge. playe 3 edge-trigger playback : a playback operation starts when this input detects a low going signal exceeding the specified debounced time. this pin has an internal pull-up resistor [1] and an internal debounce on both falling & rising edge. playl 4 level-trigger playback : a playback operation begins when this input detects a low going signal and remains at low. playback stops when the signal returns to high. this pin has an internal pull-up resistor [1] and an internal debounce on falling edge. v ssa 5 analog ground : v ssa is the ground for analog circuits. it is important to have a separate path for each ground back to the system ground terminal to minimize noise. mic+ 6 microphone positive input : the input transfers the signal to the preamplifier. the internal automatic gain control (agc) circuit controls the ga in of the preamplifier. an external microphone should be ac coupled to this pin via a series capacitor. the capacitor value, together with an internal 10 k ? resistance on this pin, determines the low- frequency cutoff for the isd1600b passband. mic- 7 microphone negative input : this is the inverting input to the microphone preamplifier. it provides input noise- cancellation, or common-mode rejection, when the microphone is connected differentially to the device. sp- 8 speaker negative : the sp-, class d pwm output, provides a differential output with sp+ pin to drive 8 ? speaker or buzzer. during power down or recording, this pin is tri-stated. v ssp 9 pwm ground : v ssp is the ground for pwm speaker driver. it is important to have a separate path for each ground back to the system ground terminal to minimize noise.
isd1600b series - 8 - soic / pdip pin name pin no. functions v cca 10 analog power supply : it is important to have a separate path for each power back to the power terminal to minimize the noises. decoupling capacitors to v ssa should be as close to the device as possible. v ccp 10 v ccp : power supply for pwm speaker drivers. it is important to have a separate path for each power back to the power terminal to minimize noise. decoupling capacitors to v ssp should be as close to the device as possible. sp+ 11 speaker positive : the sp+, class d pwm output, provide a differential output with sp- pin to drive an 8 ? speaker or buzzer directly. during power do wn or recording, this pin is tri-stated. agc 12 automatic gain control : the agc dynamically adjusts the gain of the preamplifier to compensate the wide range of microphone input levels. the agc allows the full range of signal to be recorded with minimal distortion. nominal values of 4.7 f give satisfactory results in most cases. connecting this pin to ground provides maximum gain to the preamplifier circuitry. converse ly, connecting this pin to power supply provides minimum gain to the preamplifier circuitry. aud 13 aud : the aud provides a single-ended current output to drive an external amplifier. during standby or recording, this pin is tri-stated. r osc 14 oscillator resistor : this enables the user to vary the record and/or playback duration of the device. a resistor connected between the r osc pin and v ssa determines the sample frequency for the isd1600b device. please refer to the duration section in section 6.1. v ccd 15 digital power supply : it is important to have a separate path for each power back to the power terminal to minimize noise. decoupling capacitors should be as close to the device as possible. led 16 led output : this pin is low during a record cycle and blinks during playback cycle. it can be used to drive an led to indicate either a record or playback cycle is in progress. note: [1] 600k (typical).
isd1600b series publication release date: jan. 23, 2007 - 9 - revision 1.2 6. functional description 6.1. d etailed d escription 6.1.1 audio quality winbond?s patented chipcorder ? mls technology provides natural high quality record and playback solution on a single chip. the input audio signals are stored directly into the non- volatile memory and are reproduced in its natural form without any compression artifacts caused by the digital speech solutions. a complete sample is stored in a single cell, minimizing the memory needed to store a single message. 6.1.2 duration the isd1600b series offer single-chip solution with record & playback duration from 6.6 seconds to 40 seconds. sampling frequency and duration are determined by an external resistor connected to the rosc pin. sampling frequency rosc isd1610b isd1612b isd1616b isd1620b 12 khz 53 k 6.6 secs 8 secs 10.6 secs 13.3 secs 8 khz 80 k 10 secs 12 secs 16 secs 20 secs 6.4 khz 100 k 12.5 secs 15 secs 20 secs 25 secs 5.3 khz 120 k 15 secs 18 secs 24 secs 30 secs 4 khz 160 k 20 secs 24 secs 32 secs 40 secs 6.1.3 flash storage the isd1600b product utilizes the on-chip flash memory pr oviding zero-p ower message storage. the message is retained for up to 100 years without power. in addition, the device can be re-recorded typically over 100,000 times. 6.1.4 basic operation the isd1600b chipcorder ? device is controlled by either the rec , or one of the two playback modes, playe and playl . the isd1600b parts are configured for simple design in single-message application. detailed operations are explained in section 6.2. 6.1.5 valert with valert option, after record, the led blin ks slowly to indicate a new message exists. once playback is performed, the led will not blink again and resume to normal operating conditions. 6.1.6 automatic power-down mode at the end of a playback or record cycle, the isd1600b device automatically enters into a low- power mode, consuming typically 1a, provided that playe , playl and rec are high (see dc parameters section). during a playback cycle, the device powers down automatically
isd1600b series - 10 - at the end of the message. during a record cycle, the device powers down immediately after rec is released to high. 6.2. f unctional d escription e xample the following example operating sequences demonstrate the functionality of the isd1600b series. 6.2.1. record a message the device starts recording from the beginning of the memory when rec transits from high to low and stays at low. a record cycle is completed when rec is pulled to high or entire memory is filled up. then an end-of-message (eom) marker is written at the end of message, enabling a subsequent playback cycle to terminate appropriately. hence, the device automatically enters into standby mode. record takes precedence over playback operation. if rec is pulled low during a playback cycle, the playback immediately halts and recording starts from the beginning of the memory. holding rec low after recording will increase standby current consumption. 6.2.2. edge-trigger playback a playback operation starts from the beginning of the memory when playe detects a low going signal exceeding the specified debounced time. playback continues until an eom marker is encountered. upon completion of a playback cycle, the device automatically enters into standby mode. during playback, a subsequent low going signal will terminate the current playback operation. holding this pin low after playback operatio n will increase standby current consumption. 6.2.3. level- trigger playback when playl switches from high to low and stays at low, a playback starts from the beginning of the memory until either an eom marker is reached, then it automatically powers down. if playl is pulled high at any time during playback, the playback operation stops immediately and the device enters into the power-down mode. 6.2.4. led operation the led is low during recording, which turns on an led as a recording indicator. however, during playback, the led blinks a few times per second to indicate a playback operation. it returns to a high when operation stops. 6.2.5. r osc operation the duration can be varied by changing the value of r osc . this means the designer has the flexibility to choose different sa mpling frequency, up to 12 khz, depending upon the needs. this feature allows frequency shifting where a recorded audio can be played back faster or slower than normal for special sound effects. another feature is a ?pause? function that can be activated by taking the r osc resistor to v cc to stop playback momentarily, and to resume when the resistor is switched back to ground.
isd1600b series publication release date: jan. 23, 2007 - 11 - revision 1.2 7. timing diagrams rec led mic+ mic- t f t r t db1 t rs figure 1: record operation
isd1600b series - 12 - sp+ sp- t ru t ps1 or t ps2 led playl t db2 odd # pulses starts playback t cyc t r t db1 playe t f even # pulses stops playback t db1 aud t ru ramps up gradually to analog ground to eliminate the "pop" at the beginning t ps1 or t ps2 slowly returns to analog ground to eliminate the "pop" at the end figure 2: playback operation
isd1600b series publication release date: jan. 23, 2007 - 13 - revision 1.2 8. absolute maximum ratings absolute maximum ratings (die) conditions [1] values junction temperature 150c storage temperature range -65c to +150c voltage applied to all pins (v ss ?0.3v) to (v dd +0.3v) power supply voltage to ground potential -0.3v to +7.0v absolute maximum ratings (packaged parts) conditions [1] values junction temperature 150c storage temperature range -65c to +150c voltage applied to all pins (v ss ?0.3v) to (v dd +0.3v) lead temperature (soldering ? 10 sec) 300c power supply voltage to ground potential -0.3v to +7.0v [1] stresses above those listed may cause permanent damage to the device. exposure to the absolute maximum ratings may affect device reli ability and performance. functional operation is not implied at these conditions.
isd1600b series - 14 - 8.1 o perating c onditions operating conditions (die) conditions values operating temperature range 0c to +50c supply voltage (v dd ) [1] +2.4v to +5.5v ground voltage (v ss ) [2] 0v input voltage (v dd ) [1] 0v to 5.5v voltage applied to any pins (v ss ?0.3v) to (v dd +0.3v) operating conditions (packaged parts) conditions values operating temperature range (case temperature) -40c to +85c supply voltage (v dd ) [1] +2.4v to +5.5v ground voltage (v ss ) [2] 0v input voltage (v dd ) [1] 0v to 5.5v voltage applied to any pins (v ss ?0.3v) to (v dd +0.3v) [1] v dd = v cca = v ccd = v ccp [2] v ss = v ssa = v ssd = v ssp
isd1600b series publication release date: jan. 23, 2007 - 15 - revision 1.2 9. electrical characteristics 9.1. dc p arameters parameter symbol min typ [1] max units conditions supply voltage v dd 2.4 5.5 v input low voltage v il v ss -0.3 0.3xv dd v input high voltage v ih 0.7xv dd v dd v output low voltage v ol v ss -0.3 0.3xv dd v i ol = 4.0 ma [2] output high voltage v oh 0.7xv dd v dd v i oh = -1.6 ma [2] record current i dd_record 20 ma playback current i dd_playback 20 ma v dd = 5.5v, no load, sampling freq = 12 khz standby current i sb 1 10 a [3] [4] input leakage current i ilpd1 1 a force v dd [5] input current high i ilpd2 -3 -10 a force v ss [5] preamp input resistance r mic+, r mic- 20 k ? across both pins mic input voltage v in 15 300 mv peak-to-peak [6] gain from mic to sp+/- a msp 6 40 db v in = 15 to 300mv, agc = 4.7f, v dd = 2.4v to 5.5v output load impedance r ext 8 ? speaker load 670 mw v dd = 5.5v 313 mw v dd = 4.4v 117 mw v dd = 3v speaker output power pout 49 mw v dd = 2.4v 15mvp-p 1khz freq sinewave, r ext = 8 ? ; speaker output voltage vout v dd v r ext = 8 ? (speaker), typical buzzer aud i aud -3.0 ma v dd =4.5v, r ext = 390 ? total harmonic distortion thd 1 % 15mv p-p 1khz sinewave, cmessage weighted notes: [1] conditions: v cc = 4.5v, 8khz sampling frequency and t a = 25 c , unless otherwise stated. [2] led output during record operation. [3] v cca, v ccd and v ccp are connected together. v ssa , v ssp and v ssd are connected together. [4] rec , playe and playl must be at v ccd . [5] rec , playe and playl are forced to specified condition. [6] balanced input signal applied between mic and mi c ref as shown in the applications example. single- ended mic or mic ref recommended to be less than 100 mv peak to peak.
isd1600b series - 16 - 9.2. ac p arameters characteristic symbol min typ [1] max units conditions sampling frequency [2] f s 4 12 khz vcc=2.4v~5.5v i1610b i1612b i1616b i1620b 6.6 8 10.6 13.3 sec sf=12khz 10 12 16 20 sec sf=8khz 12.5 15 20 25 sec sf=6.4khz 15 18 24 30 sec sf=5.3khz duration [3] dur 20 24 32 40 sec sf=4khz vcc=2.4 v~5.5v rising time t r 0 100 nsec falling time t f 0 100 nsec 26.6 26.6 26.6 26.6 msec sf=12khz 40 40 40 40 msec sf=8khz 50 50 50 50 msec sf=6.4khz 60.4 60.4 60.4 60.4 msec sf=5.3khz debounce time (record & playl) t db1 80 80 80 80 msec sf=4khz vcc=2.4 v~5.5v 13.3 13.3 13.3 13.3 msec sf=12khz 20 20 20 20 msec sf=8khz 25 25 25 25 msec sf=6.4khz 30.2 30.2 30.2 30.2 msec sf=5.3khz debounce time (playe) t db2 40 40 40 40 msec sf=4khz vcc=2.4 v~5.5v signal ramp up time t ru 100 msec vcc=2.4v~5.5v record stop time t rs 2 sample clock vcc=2.4v~5.5v playl stop time t ps1 t db1 msec vcc=2.4v~5.5v playe stop time t ps2 2 x t db1 msec vcc=2.4v~5.5v led cycle frequency t cyc 1 6 hz playback at any sf notes: [1] typical values : v cc = 4.5v, sampling frequency (sf) = 8 khz and @ t a = 25 c , unless otherwise stated. [2] sampling frequency can vary as much as 2.25 percent over the commercial temperature and voltage ranges, and ?6/+4 percent over the indust rial temperature and voltage ranges. [6] duration can vary as much as 2.25 percent over the commercial temperature and voltage ranges, and ? 6/+4 percent over the industrial temperature and voltage ranges.
isd1600b series publication release date: jan. 23, 2007 - 17 - revision 1.2 10. typical application circuit the below example illustrates a typica l applications of isd1600b device. isd1600b aud mic+ mic - agc c4 vcc gnd r osc r4** r7* v ccd rec playe playl led r6 v cca 4.7 f 4.7 k 0.1 f 4.7 k 0.1 f 4.7 k 4.7 f electret microphone v ccd v cca v ssd v ssa v ssp c6 c10* c9* 0.1 f 0.1 f c11* 0.1 f v ccp sp+ sp- speaker or buzzer r5 390 0.1 f c5 v cc q1 8050 speaker c8 c7 di led 1 k v cca v ccd v ccp 2 3 4 14 12 16 15 1 10 5 10 9 13 11 8 6 7 r1 r2 r3 c1 c2 c3 *** *** optional: based upon the applications schematic shows both speaker and aud outputs notes: * these components may be needed in order to optimize for the best voice quality and system performance, which is also dependent upon the layout of the pc b. pending upon system requirement, cx can be 10 f, 4.7 f or other values. for r7, 1k gives satisfactory result fro most cases. ** for sampling freq at 8 khz, r4 = 80 k *** it is important to have a separate path for each gr ound and power back to related terminal to minimize the noise. also, the power supplies should be decoup led as close to the device as possible. good audio design practices winbond?s chipcorder are very hi gh-quality single-chip voice recording and playback devices. to ensure the highest quality voice reproduction, it is important that good audio design practices on layout and power supply decoupling are followed. see application information links below for details. design considerations for isd1600b series http://www.winbond-usa.com/products/isd_product s/chipcorder/applicationbriefs/an-cc1001.pdf good audio design practices http://www.winbond-usa.com/products/isd_produ cts/chipcorder/applicationinfo/apin11.pdf single-chip board layout diagrams http://www.winbond-usa.com/products/isd_produ cts/chipcorder/applicationinfo/apin12.pdf
isd1600b series - 18 - 11. package drawing and dimensions 11.1. 16-lead 150mil small outline inte grated circuit (soic) package
isd1600b series publication release date: jan. 23, 2007 - 19 - revision 1.2 11.2. 16-lead 300mil plastic dual inline package (pdip)
isd1600b series - 20 - 11.3. die physical layout isd1610b / 1612b / 1616b / 1620b v ssa mic+ mic- sp- sp+ v ssp v cca v ccp agc aud playl v ccd r osc v ssd led playe rec v ccp notes: 1. the backside of die is internally connected to v ssa . it must not be connected to any other potential or damage may occur. 2. for package, v cca and v ccp pads are bonded together to one pin.
isd1600b series publication release date: jan. 23, 2007 - 21 - revision 1.2 12. ordering information product number descriptor key when ordering, please refer to the following valid part numbers that are supported in volume for this product series. contact the local winbond sales representative or distributor for availability information. for the latest product information, access winbond?s worldwide website at http://www.winbond-usa.com isd16xxx x x x xx product series: isd1600 series duration : 10b : 6.6 ? 20 secs 12b : 8 ? 24 secs 16b : 10.6 ? 30 secs 20b : 13.3 ? 40 secs package type : x = die p = plastic dual inline package (pdip) s = small outline integrated circuit (soic) package temperature : i = industrial (-40 c to +85 c) blank = commerical ? die (0 c to +50 c) ? package (0 c to +70 c) special features field : blank = valert disabled 01 = valert enabled package option : y = lead-free blank = leaded
isd1600b series - 22 - 13. version history version date description a1 apr 2005 initial version 1 jan 2006 change to preliminary update ordering info with pb-free option 1.1 apr 2006 update application diagram 1.2 jan 2007 update rosc resistor value revise automatic power down mode update standby current parameter revise die physical layout section
isd1600b series publication release date: jan. 23, 2007 - 23 - revision 1.2 winbond products are not designed, intended, authorized or wa rranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instru ments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. furthermore, winbond products are not intended for applications wherein failure of winbond products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify winbond for any damages resulting from such improper use or sales. the contents of this document are provided only as a guide for the applications of winbond products. winbond makes no representation or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to discontinue or make changes to specif ications and product descriptions at any time without notice. no license, whether express or implied, to any intellectual prop erty or other right of winbond or others is granted by this publication. except as set forth in winbond's standard terms and conditions of sale, winbond assumes no liability whatsoever and disclaims any express or implied warrant y of merchantability, fitness for a particular purpose or infringement of any intellectual property. the contents of this document are provided ?as is?, and winbond assumes no liability whatsoever and disclaims any express or implied warranty of merchantability, fitness for a particular purpose or infringement of any intellectual property. in no event, shall winbond be liable for any damages whatsoever (including, without limitation, damages for loss of profits, business interruption, loss of information) arisi ng out of the use of or inabilit y to use the contents of this documents, even if winbond has been advised of the possibility of such damages. application examples and alternative uses of any integrated ci rcuit contained in this publication are for illustration only and winbond makes no representation or warranty that such applications shall be suitable for the use specified. the 100-year retention and 100k record cycle projections are based upon accelerated reliability tests, as published in the winbond reliability report, and are neither warranted nor guaranteed by winbond. this product incorporates superflash ? . this datasheet and any future addendum to this datasheet is(are) the complete and controlling isd ? chipcorder ? product specifications. in the event any inconsistencies exist between the information in this and other product documentation, or in the event that other product documentatio n contains information in addition to the information in this, the information contained herein supersedes and governs such other information in its ent irety. this datasheet is subject to change without notice. copyright ? 2005, winbond electronics corporation. all rights reserved. chipcorder ? and isd ? are trademarks of winbond electronics corporation. superflash ? is the trademark of silicon storage technology, inc. all other trademarks are properties of their respective owners.

▲Up To Search▲

Price & Availability of ISD1620BPYI01

	To Download ISD1620BPYI01 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .